Skin Enhancer

With this tool, we recommend using the QÚL Beauty Anti-Aging Moisturizer or Firm & Hydrate Mask with a few sprays of Hydrating Rose Water. You may add a few drops of Glo Serum for extra hydration. Use QÚL’s Exfoliating Cleanser for deep cleanse mode.

• Ultrasonic Cleansing: ultrasonic vibrations exfoliate the superficial layers of the skin, reviving skin tissue. 
• EMS (electrical muscle stimulation/nano current): may help reduce the signs of aging by helping firm and smooth the skin. 
• Biomechanical Vibrations — sends gentle vibrations (6000-7000 times per minute): may help stimulate the muscles through contraction and relaxation, helping tone the skin. 
• Heat – warm massage promotes the absorption of products and may help create a smoother texture to the skin
• Red Light – 640nm-650nm red light may help reduce fine lines and wrinkles
• Blue Light – 460nm-470nm may help calm skin
• Orange Light – 597nm-622nm may help repair and tone the skin
• Cooling – may help tighten pores and lock in moisture

The Skin Enhancer consists of six modes. 

*Please read charging instructions before first use.

1. Hold the power button to turn the device on. 
2. Press the modality button to select Mode (see modes below). 
3. Press the Intensity Button to adjust the intensity level. 

*All modes include vibration to simulate muscles. You can change the level of vibration with the intensity button. EMS will also show up in all modes. You can shut off EMS or change the power level of EMS to any mode by quickly pressing the on/off button. There are five levels for EMS, the sixth press will turn EMS off. A seventh press will bring it back on to level one. 

Mode 1:

• Ultrasonic Cleansing:  You can use ultrasonic cleansing mode with or without a cotton pad. If you don’t wear base makeup, no need to apply the cotton pad. 

1. Put a damp cotton pad on head of unit (remove the plastic ring, place a cotton pad on the head and place the plastic ring back on).
2. Apply Exfoliating Cleanser to face. Using circular movements around the face for 2 to 3 minutes, this mode can effectively clean the dirt from the pores making the skin translucent. 
3. OR Apply cleanser to face and use unit without cotton pad over the cleanser. Using circular movements around the face for 2 to 3 minutes. 
4. Frequency of use: 2-3 times a week. Reduce to once a week for sensitive skin.

Mode 2:

• Seep: This mode includes EMS, Biomechanical Vibration, and Red LED for rejuvenation. 

1. Apply tone to a cotton round, and place on the head of unit. Place plastic ring on top of gauze. 
2. Gently glide across face for 1 to 2 minutes. This allows for a deeper cleanser, making sure that all makeup has been removed. (If you don’t wear makeup, you don’t need to use this mode). 

Mode 3:

• Lift: This mode includes EMS, vibration, and heat. Best mode for toning and tightening. 

Mode 4: 

• Restore: This mode includes EMS, vibration, and LED. This is your nourishing mode for driving the product deeper into the skin. Great for dehydrated skin or if there is an ingredient you want to drive deeper into the skin (i.e.: for pigmentation). You can use this with red, blue, or orange LED. Just press the mode button to change the LED color.

Mode 5: 

• Eye: Gentle pulses stimulate sensitive eye area. Use a light pressing technique around the eye. Hold and press for two seconds, lift, and move to the next area. Repeat. Apply eye product first.

Mode 6: 

• Cold: This mode includes blue LED light for calming. Use around puffy eyes, over pimples to calm, or over full face to lock in products. Try this mode if your skin needs calming from irritation. You can still use the EMS and vibration to tone while calming your skin!

How to Use:

1. Apply QÚL Products (please see recommended products)
2. Select Mode
3. We recommend starting with the Cleanse (mode 1), then Seep (mode 2), then Lift (mode 3) 
4. Gently glide the tool across your face in upward and outward movements. 
5. Use for 5 minutes  (tool automatically turns off after 5 minutes). 
6. Turn device back on and use Restore (mode 4) for 5 minutes. 
7. If wanted, use Eye (mode 5) for 60 to 90 seconds around each eye (and lips)
8. Finish in cold mode (mode 6) for 60 to 90 seconds. 
9. Do not remove product. This tool will lock in the moisture for more hydrated-looking skin. 
10. Finish with SPF. 

Charging

Do not use a power cord other than the one supplied with the Skin Enhancer as this may cause a malfunction. Be sure to charge the unit before using it. Please use the plug supplied in your package. The charging indicator will blink while the unit is charging. When the unit is completely charged (approximately 2 hours) the blinking will stop.

There is a power indicator in the top left corner when the unit is turned on. This will indicate how much power is left in the unit. Please do not leave the unit continually plugged in when not in use. This can shorten the life of the unit. When not in use for long periods, please charge the unit every 3 months. This will increase the longevity of the unit.

*Important Please Read*

*When the unit is turned off, press, and hold the power button for 2 seconds to turn the unit on. The unit will begin in the ultrasonic cleansing, EMS, and vibration mode.

*When the power is already on, a short press to the mode button will switch to the next mode. *When the unit is on, a short press on the + and – keys will adjust the intensity. It goes up to level 5 When you press a 6th time it will go back to level one.

*All modes include vibration to stimulate muscles. This is a good thing!! You can change the level of vibration with the “intensity” button. EMS will also show up in all modes. You can shut off EMS or change the power level of the EMS to any mode by quickly pressing the on/off button. There are 5 levels of EMS. The sixth press will turn EMS off. A 7th press will turn it back on to level one.

*There needs to be product on the face for all modes except cold.

*When using this unit please be sure to place the head flat on the skin so the full surface area is touching. There are sensors in the head and if the full surface area is not on the skin, the sensors cannot do their job!

Cleaning After Use

Clean unit with damp soapy cloth. Wipe with a dry cloth. Do not immerse unit in water. Do not use in shower. Carefully wipe removable plastic ring with damp soapy cloth. Do not use corrosive solutions such as alcohol to clean your skin enhancer.

Please go to HERE to download the training PDF.